FUCK FUCK FUCK

[Antee]

ayo sp headz, i have noticed that one of my pad (the number 1) is kinda fucked up... it works but i must push it harder, it's not sensible as the other padz, can i do something or i'll must change the pad?

[tape smoke]

my pad 10 is the same, after a while of rubbing it , it works a bit better,

i usually avoid using it,

[Dj_just_jeff]

after a while of rubbing it , it works a bit better,
he he he...

It is possible that the sensor is worn. There also could be some FUNK in there. Take the think apart and peep the MUNG that is holding you up.

[wax inspektor]

it's not possible to change a single pad...

the sensor isnt the problem for sure, it's just the fucking rubber that's shredded (?) round the pad... think it#s nearly impossible to get a new pad mat for the OG 404 these days... seems like it's time for a SX Antee... that pad material is a bit better...

[cartesia]

might just be gunk on the contacts, open it up and see if theres any dirt on the contacts under the rubber pads

[shabbster]

there really inst any supply for the classic 404 mat anymore?
that sucks. mine is about the break anytime soon...
what do the 303 and/or the 202 users regarding this problem?

[Euclid Ov Oåklånd]

Buy a midi pad device, or just don't beat on them so hard.

[Les Braun]

Antee! Where you been
What've you been up to, man?

[wax inspektor]

How about SX pads in an og 404?!

...since it's mainly the pads goin down, og 404 users could get a SX mat and cut it right above line 'pad1-hold'... just replace it with the old part of the mat and done...
you could hot glue it or use some silicon but i don't think thats necessary... sure you could use the whole sx mat, but i think thats too confusing... might work for ebay though.

IMG_5996_640x480.JPG (11.57 KiB) Viewed 7224 times

[shabbster]

thats maybe worth a try!
where to buy them?

[wax inspektor]

i got mine from a roland dealer... i would contact roland, so they can tell you an authorized dealer in your area, maybe they still have old ones under the desk as well... i'd say go for it, the back of the mat is already a bit perforated at the right position; makes a clean cut easy...

i'd love to see the result.

[tape smoke]

i took my 404 apart this morning and cleaned it out with duster, there was some grime on the sensor and rubber , then i put it back together and all the pads work even better. !

[cartesia]

^ yup!

The 'sensor' is just 2 bits of metal (and when u push a pad down, the carbon bits on the bottom of it connect the 2 bits of metal, causing the trigger)...

so fixing pad problems should 99% of the time be nothing more than a case of cleaning

[wax inspektor]

lucky dude... my shit wasn't dirty at all... the material was dry and brittle so the pads broke out of the mat. I'm quite convinced that there are 2 series of mats for the 404, cause the one I have now + the 404 I bought a year ago def feeling different from the "oct 05" model...

I just ordered a SX mat and I'm going to put it into my old 404 (at least the pad section). I've cut my old mat into 2 piece to try stuff out, and yo hot glue is my friend... not for sniffin though.

[cartesia]

There do seem to be 2 different 404 pads..

I have a 'new' normal 404 - the pads feel different to the original ones, and also the body/case of the latest 404s is shaped like the 404SX - not as tall and with less of a sloping face than the original 404s, and with shorter knobs (less likely to break off in my bag)