Mixing

Kei Kurono · Post by **Kei Kurono** » Wed Mar 13, 2013 11:31 pm

Why does my mix sound different when I track it out of my sp ?

springwater · Post by **springwater** » Wed Mar 13, 2013 11:50 pm

Is your SP using stereo samples then you track it out to mono? What are you recording into? Computer?

hseiken · Post by **hseiken** » Thu Mar 14, 2013 1:13 am

That question is really vague. Can you elaborate with examples?

Kei Kurono · Post by **Kei Kurono** » Fri Mar 15, 2013 1:39 am

No, I always track out to stereo. I had been using audacity and a cheap behringer interface to track out. For example the mix wouldn't sound as fat once it was tracked out. I've also had problems before where I have to track out with very low volume on the sp or it would overdrive like crazy on audacity. recently I started using reaper to track out and using my sp 555 as the interface. idk how to explain but it just sounds like it loses some quality after I track out (wav file). I usually fix all that with izotope but I was just wondering if you guys could help me out with some tips.

MattCoops · Post by **MattCoops** » Fri Mar 15, 2013 4:46 am

You mean, when you play your stuff on the SP it sounds nice, but when you record into your computer, it doesn't sound as nice?

knobsmcgee · Post by **knobsmcgee** » Fri Mar 15, 2013 5:04 am

are you monitoring your SP and cpu with the same thing?

MattCoops · Post by **MattCoops** » Fri Mar 15, 2013 5:35 am

If you are recording into Audacity, try this:

Before recording, click on Edit > Preferences

on "Recording" check the box for Software Playthrough.

This allows you to monitor through the computer your recording signal.
Now click the pause button, then record. Play some stuff through the SP.
How does it sound?

EndorShores · Post by **EndorShores** » Fri Mar 15, 2013 8:05 pm

Howdy, I noticed that when I record thru usb with 555 as soundcard it comes out quiete. So i started using a interface with a stereo in to run headphone jack of 555 into stereo in of interface. This gives me an extra gain which is nice. Anywho, try holding cancel then hold start/end/level button then turn ctrl knob 3. This gives u db gain to 12. I usually keep mine at six everytime I startup.

Kei Kurono · Post by **Kei Kurono** » Sat Mar 16, 2013 8:06 pm

Thanks for the tip Endor i'm going to try that out.

Probotector · Post by **Probotector** » Mon Mar 25, 2013 9:57 pm

I had a cheap behringer interface too, but that was awful. The record-quality on my laptop onboard soundcard was better. Maybe you buy a better interface.

I stopped recording with my laptop and only use my desktop pc with a esi juli soundcard.

theemikeb · Post by **theemikeb** » Wed Apr 03, 2013 1:37 am

I've had this same issue when tracking beats out from my 303, 404 and 2000xl. Not sure why. Ill track it all out then ill play back from the sampler for a second and from the computer for a second...the recording sounds slightly diiferent. Its difficultto explain but maybe...less warmth? I record into stereo/mono depending what the sample is through an audiobox usb into my Vaio in Cubase

Freezerbitten · Post by **Freezerbitten** » Fri Aug 09, 2013 12:02 am

Analyze your entire signal chain from start to finish. That's kind of a technical question that one would need alot of details about your chain to answer. Most will tell you to replace the behringer...but that might not be it at all.

It may be the track settings in Cubase used to record. You also might be choking the volume somewhere between the SP and the final track.

Try to normalize the SP track after it's recorded.

pele253 · Post by **pele253** » Mon Aug 12, 2013 8:39 am

red & white rca's out...into the interface...make sure your interface driver is installed properly...and the buffer sample rate is set...

SP-FORUMS

Mixing

Mixing

Re: Mixing

Re: Mixing

Re: Mixing

Re: Mixing

Re: Mixing

Re: Mixing

Re: Mixing

Re: Mixing

Re: Mixing

Re: Mixing

Re: Mixing

Re: Mixing