Tape deck

khuf1 · **Joined:** Sun Aug 14, 2011 10:34 am **Posts:** 35

Bought some tapes today and im trying to record it to my digital recorder so i can use it for the sampler. when i listen to the stuff on the digi recorder the sound is a mess? Ive never done this before, so it would be good to know what im doing wrong

LimpyLoo · **Joined:** Fri Jul 22, 2011 5:58 am **Posts:** 387

can you be more specific about what it is that you're doing? What gear is involved and what is going where?

khuf1 · **Joined:** Sun Aug 14, 2011 10:34 am **Posts:** 35

After i recorded from the tape deck to the digital recorder the sound is a mess. Its some akai tape deck thats hooked up to akai amplifier, would it be better to use the sampler instead of the digital recorder? how do you do it?

khuf1 · **Joined:** Sun Aug 14, 2011 10:34 am **Posts:** 35

the sound is like its peaking like shit, but i tried to lower the volume on the amplifier and the digital recorder but its the same

LimpyLoo · **Joined:** Fri Jul 22, 2011 5:58 am **Posts:** 387

khuf1 wrote:

would it be better to use the sampler instead of the digital recorder?

for the sake of telling what is causing problem, you should do this. if it's still a mess, then you will know who dunnit!

(that is, who is the cause of the mess, the tape deck or the amp or the digital recorder)

Mr. Davenport · **Joined:** Sat Oct 17, 2009 11:00 pm **Posts:** 430

make sure your levels are good before the initial recording. so, when you are recording from one thing to the next, make sure the source is about as loud as possible before going to the next device. the device that is on the recieving end should have inputs set as low as possible all while trying to get the maximum input. if this is indeed the problem, most unwanted noise will be eliminated.

khuf1 · **Joined:** Sun Aug 14, 2011 10:34 am **Posts:** 35

thx ill try that!

KOMSAT · **Joined:** Sat Nov 27, 2010 12:53 am **Posts:** 323

Lemme hear that tape hissssss khu.

khuf1 · **Joined:** Sun Aug 14, 2011 10:34 am **Posts:** 35

foshO! them tapes was raw, found some indian spice beats!

Unfolding · **Joined:** Sun Jan 03, 2010 2:42 am **Posts:** 952

Dorkus wrote:

make sure your levels are good before the initial recording. so, when you are recording from one thing to the next, make sure the source is about as loud as possible before going to the next device. the device that is on the recieving end should have inputs set as low as possible all while trying to get the maximum input. if this is indeed the problem, most unwanted noise will be eliminated.

2nd. To add to Dorkus' method: if the next device in the chain can show when the audio peaks, try to avoid the peak as best as possible. It'll sound cleanest when the peak only just flashes/hits on the loudest sound of the sample.

Mr. Davenport · **Joined:** Sat Oct 17, 2009 11:00 pm **Posts:** 430

khuf1 wrote:

After i recorded from the tape deck to the digital recorder the sound is a mess. Its some akai tape deck thats hooked up to akai amplifier, would it be better to use the sampler instead of the digital recorder? how do you do it?

Why not just sample it directly into your sampler? Why would it be necessary to go into the tracker first?

KOMSAT · **Joined:** Sat Nov 27, 2010 12:53 am **Posts:** 323

Dorkus wrote:

khuf1 wrote:

After i recorded from the tape deck to the digital recorder the sound is a mess. Its some akai tape deck thats hooked up to akai amplifier, would it be better to use the sampler instead of the digital recorder? how do you do it?

Why not just sample it directly into your sampler? Why would it be necessary to go into the tracker first?

I was kind of thinking this as well. Unless you're "archiving" tape stuff? I do that with vinyl sometimes, record a couple full records (especially if I'm borrowing from a friend) for later sampling.

khuf1 · **Joined:** Sun Aug 14, 2011 10:34 am **Posts:** 35

yea it's for recording the whole shiznit and then use it for later

but ill try the sp and the other advices

Tape deck

Who is online